NetAgent UPS SNMP Agent User’s Manual

3.2 Pictures of NetAgent NetAgent II(BN,BK,CK Series) BN506 BN514 BK514 CK504 BN505 BN513 BK513 NetAgent Mini (DK Series) DK530 DK520 D

3.3 NetAgent Package Contents Netagent has three models: “Internal/External”; “1 phase/3 phase”; and “1 port/3 port”. The different model has differen

♦ 3 Port NetAgent (Internal / External) : LED Table Yellow Red Green Status Solid Off Solid Off Solid ON Power ON Flashing Solid ON Soli

3.5 NetAgent Mini Out looking NetAgent Mini External NetAgent Mini Internal Module To UPSTo LAN (LAN Port LED) Status LED To LAN (LAN Port LE

Chapter 2. NetAgent UPS Installation Before using the NetAgent, the proper hardware and software configuration is necessary. Hardware installation

Chapter 3. NetAgent, UPS and Network Connection NetAgent II and NetAgent Mini provides External and Internal model for different UPS interface requir

Section2. Install the NetAgent Mini with UPS and Network NetAgent Mini - External NetAgent Mini -Internal To UPSTo DC AdapterTo UPS To LANTo L

Chapter 4. Using Netility Setup IP.Update Firmware Section1. Install Netility  Insert NetAgent Utility CD to the CD-ROM driver and execute Netili

 NetWork Selection After execute Netility, Netility would search computer’s internet card automatically, or, click on Network Selection from the main

Advanced:Advanced Netagent UPS Setting In order to ensure the secure management of UPS, Netility provides two protecting function: Netility Password A

User Guide for the NetAgent Version 3.30 Firmware version 2.35 Copyright Information Copyright © 2000-2004, Mega System Technologies, Inc. All right

Note:Net Agent provided well-considerable protection function. If uploading was interrupted and raised data in incomplete, Net Agent will keep its de

Chapter 5. UPS Web management by NetAgent Section1. Introduction After finishing NetAgent installation, including hardware installation and IP setting

2.1 Information Sub-Menu : 2.1.1 System Status 2.1.2 Basic Information 2.1.3 Current Status 2.1.4 Remote Control 2.1.5 Meter/Chart 2.1.6 Environmen

2.1.2 Basic Information This page is to show UPS basic information. Values here are either provided by the UPS or they are user settings from the Conf

Fig.21 Current Status 2.1.4 Remote Control This page is to provide remote UPS test functions. Choose the test item, then click on 'Apply' t

2.1.5 Meter/Chart This page displays temperature, capacity, load, voltage..etc of the UPS by appearing with metres diagrams. Fig.23 Meter/Chart 2.1.6

Fig.24 Environment Sensors - NetFeeler Lite 2.2 Configuration Sub-Menu : 2.2.1 UPS Configuration 2.2.2 UPS On/Off Schedule 2.2.3 Network 2.2.4 SN

Last Battery Replaced Date ( mm/dd/yyyy) This section is to record the date when the UPS battery was last replaced. UPS Recorded UPS Data Log T

2.2.2 UPS On/Off Schedule This page is to schedule On/Off time for the UPS. Weekly Schedule This section is to set the time to turn on/off the UPS

Primary DNS Server IP This section is to set NetAgent primary DNS Server IP address. Secondary DNS Server IP This section is to set NetAgent sec

Contents Chapter1. Introduction_________________________________________ 1 Section1. Features __________________________________________ 1 Section2. A

Trap Notification Receiver IP Address This section is to set receivers IP address for receiving traps sent by NetAgent. It is valid for up to 8 IP

2.2.5 Email This page is to set Email details for use by NetAgent. Email Server This section is to set NetAgent Email Server . Sender’s Email Ad

2.2.6 WEB/Telnet This page is to set up the User Account in NetAgent. User Name This section is to set a user name for NetAgent web pages. It is v

2.2.8 NetFeeler Lite This page is to set Environment sensors-NetFeeler Lite configurations. Critical UnderRun This section is to set the lowest cr

2.3 Log Information Sub-Menu : 2.3.1 Event Log 2.3.2 Data Log 2.3.3 Save Data Log Note: This page’s selection would differ according to the differn

Fig.35 Date Log 2.3.3 Save Data Log This function is to record RS232 UPS’s voltage, frequency, load, capacity, temperature..etc to save as another fi

Chapter 6. Telnet (Remote Monitoring) Section1. Introduction NetAgent supports multiple Network Management systems and LAN protocols. After finishing

Fig.40 NetAgent Telnet window ♦ Set IP Address. This function allows you to setup IP Address, Gateway Address, Subnet Mask parameters. ♦ Set SNMP MI

Chapter 7. ClientMate - Windows Shutdown Utility ClientMate is a utility for connecting to the RUPS 2000, UPSilon 2000 and NetAgent. This utility is

2.1 Configuration When the ClientMate gets the signal from the NetAgent about the AC power failure or battery low signals, the ClientMate will based o

2.1.5 Meter/Chart________________________________________ 20 2.1.6 Environment Sensors-NetFeeler Lite ____________________ 20 2.2 Configuration_______

♦ When Battery Low, commence computer shutdown sequence in xx Min. To configure the time delay between the Battery Low and system shutdown. ♦ Notify

2.4 IP address of connection Status ICON Description Already connect to NetAgent UPS at IP 211.21.67.51 Does not connect to any NetAgent. 2.5 A

Chapter 8. SNMPView – Windows Based UPS Management System SNMPView is a software to remotely monitor and control multiple UPS connected to a netwo

Section3. Install SNMPView 3.1 Install SNMPView  Put the NetAgent Utility CD into the CD driver. And execute the SNMPView program.  After installati

3.2 Using SNMPView When use SNMP view at the first time, the system will ask for input the user's lease enter the default value as follows to sta

3.3 SNMPView Buttons Enh all SNMP hosts that supports Public group and etAgent on network and in the main umerate : Searcdisplay them on the screen

3.3.2 ADD UPS Click “Add UPS” to enter the IP address of the UPS manually. Once entered, the UPS will be shown on the main list. 3.3.3 DELETE UPS Cli

“Email” Tab Click the “Email” tab from the settings windows to configure the SNMPView E-mail Warning configuration, diagram shown below: ♦ Sender Disp

Trap List Double click to edit the Trap settings. This sets the trap notification. UPS Loading This determines the UPS loading. Double t

“Meter” Tab temperature of the UPS, in Fahrenheit The “Meter” tab displays the following information; ♦ Input Voltage: Show the voltage input from A

Section3. Install SNMPView__________________________________ 38 3.1 Install SNMPView ______________________________________ 38 3.2 Using SNMPView ____

“Digital” Tab Display (highlighted in blue) thcurrent input and oute put voltage, put frequency, battery capacity, U t als minimum encountered values

“Control” Tab nother 1 minute. • Flash LED: Flash the UPS’s LED display. (Optional function of the UPS) • Cancel Shutdown: The UPS will cancel the “

3.3.7 VIEW Lar ge Icon View mall Icon View S Detail View 47

3.3.8 EVENT LOG • This button records and lists events for a particular UPS. 3.3.9 DATA LOG • Records data of all UPS listed. 3.3.10 OPTION Sets

MENU Device Add Group • Add a new Group folder into the main list User to enter group name • Export Configuration Save the configuration in .dat c

Help • Contents: This help menu • About Gives the current SNMP version, license and contact /fo mail. in50

Appendix - Update the fiing convenient methods for user to update the late 1. nload Firmware” function under Netility to update it (suitable for all

4. h Again, the password here is the one been set at Netility, if did not set anything before, Use IE browser to update (suitable for BK,CK,DK vers

53

Chapter1. Introduction Section1. Features NetAgent is a new generation SNMP (Simple Network Management Protocol) monitoring product. Not only c

Section2. Applications 2.1 NetAgent makes your UPS on the Internet When the UPS install the NetAgent, the system manager could check each and every UP

Fig.1 NetAgent connection Software Fig.2 3 Port NetAgent II Diagram 3

Section3. NetAgent Models 3.1 NetAgent Models NetAgent II Model P/N Package Contents Internal/External 1/3 Port 1/3 phase504 1. 1Port Internal 2. N